24V Control Module for Razor Dirt Quad Version11+, With 5 Connectors, 6 Pins Throttle, Model: HB2430-TYD6-FS-ROHS

24V Control Module for Razor Dirt Quad Version11+, With 5 Connectors, 6 Pins Throttle, Model: HB2430-TYD6-FS-ROHS

Sale: $20.99 $8.40
Save: 60% off
Ends tomorrow!

Free shipping & returns on orders over 49.
7-Day no reason to return.
Description

Note:

Model versions can be determined based on the product ID code on your Razor product. The product ID code can be found on the battery cover and/or on the bottom of the frame. The 7th and 8th numbers in your product ID code are the version number of your Razor product (e.g. "01" = Version 1, "02" = Version 2, etc.)

Warm Tips:

  • Most electric scooters and electric bikes have controllers which were made specifically for that model. Please carefully confirm the model number of controllers before buying.
  • If a controller is available that will plug-and-play directly into an electric scooter or bike, however the controller is not listed by make and model, be careful when installing it because the wiring patterns going to the connectors may be different than that of the original controller. Double check the wiring to make sure that it is correct before installing the new controller. If the connectors are correct but the wiring going to the connectors are incorrect the pins can be removed and installed in different locations on the connector.
  • Sometimes the brake switch becomes defective and locks into the on position which makes the controller turn off the motor. If the scooter works after disconnecting the brake switch then the brake switch is defective.

  • Razor replacement control module for the Razor Dirt Quad, versions 11 and up. This controller includes a throttle connector with 6 pins.
  • Razor Part Number: W25143069015
  • Controller Model Number: HB2430-TYD6-FS-ROHS

Compatible with:

Razor Dirt Quad, Version 11+

Razor Sport Mod (All Versions)

Razor E200, Versions 1-4

Razor E200, Versions 5-12

E300(E300S、E325), Versions 1-10、 12( Except 11)

Razor MX350 (Versions 1-32)

Razor MX400 (Versions 1-32)

Razor Pocket Rocket (Versions 7-26)

Razor Pocket Mod (Versions 13-44)

Compatible with:

Razor Pocket Mod Betty

Razor Pocket Mod Bistro

Razor Pocket Mod Chrissy

Razor Pocket Mod Daisy

Razor Pocket Mod Hannah Montana

Razor Pocket Mod Kiki

Razor Pocket Mod Sweet Pea

Razor Pocket Mod Vapor

Razor Pocket Mod Bella

Razor Pocket Mod Blossom

Controller Installation Tips:

1. Before replacing the controller make sure that the key switch or power switch is in the off position.

2. Disconnect the battery pack from the controller first when removing a controller, and connect the battery pack to the controller last when installing a controller.

3. Hang or block the rear wheel off the ground, or remove the chain or belt from the motor before connecting the battery pack to the controller. Sometimes due to damaged or incorrect wiring or faulty electrical components the rear wheel might spin uncontrollably when making the final wiring connection to the battery pack.

4. Do not short-circuit the battery terminals or wiring harness connector pins and make sure the batteries fit snug into place and that all of the wiring and connectors are in good serviceable condition.

  • Make sure this fits by entering your model number.
  • 24V Razor Dirt Quad controller with 5 connectors. Compatible with: Razor Dirt Quad Version11+
  • This controller includes a throttle connector with 6 pins
  • Razor Part Number: W25143069015
  • Controller Model Number: HB2430-TYD6-FS-ROHS
  • Note: Model versions can be determined based on the product ID code on your Razor product. The product ID code can be found on the battery cover and/or on the bottom of the frame. The 7th and 8th numbers in your product ID code are the version number of your Razor product (e.g. "01" = Version 1, "02" = Version 2, etc.)


Reviews (0)
Cart